• WE DO LONG RANGE RIGHT.

    JOIN LONG RANGE ONLY

    Ask questions. Share your experience. Talk rifles, reloading, optics, and hunting with people who put their gear to work.

    REAL EXPERIENCE.   SHARED KNOWLEDGE.
    JOIN THE COMMUNITY →
    Free account. Be part of the conversation.
    Already a member? Log in

Why bed a barrel? Bedding vs free-floating

jeffpatton00

New member
Joined
Mar 22, 2020
Messages
11
Reaction score
4
Points
3
There's a lot of information on bedding barrels in bolt guns, but I'd like to better understand why bedding is a good thing. In a gas gun, a free-floating barrel is usually preferred for precision, its only connection to the rifle is where it mates to the upper receiver (and of course the gas block), which I believe is intended to minimize contacts which would affect barrel harmonics.

In a bolt gun, however, it's apparently preferred to bed the barrel into the stock, so in my (limited) understanding, this runs counter to the preferred approach with a gas gun. Can you help me understand why minimizing barrel contact is a good thing in a gas gun, but maximizing barrel contact is preferred in a bolt gun? Further, since release agent is used when bedding and the barrel isn't glued to the stock, the barrel is still able to vibrate against the bedding due to harmonics, and potentially able to contact the bedding at different locations at different points in the harmonic sine wave. My application is precision target shooting, if that bears on the issue. Thx for your info.
 

J2shooter

Well-known member
Joined
Jan 10, 2020
Messages
2,175
Reaction score
3,033
Points
113
Negative, you want the barrel floated in a bolt gun for the same reasons you want it floated in a gas gun. We do not bed barrels in the barrel channel.

You must be talking about bedding the bolt action/receiver to the stock.
Action bedding isn't always needed on a bolt action rifle..... especially if you're not having any accuracy issues at all but it's not a bad idea to bed an action anyway.

This bedding forms a very tight tolerance /form fitting and stronger connection between the action and stock and eliminates the chance for torque being introduced into the action by the action screws due to variabilities in the stock inlet.

Usually this bedding stops at the recoil lug but some will extend the bedding just a bit ahead of the lug to add some contact to the breech area of the barrel.
 

jeffpatton00

New member
Joined
Mar 22, 2020
Messages
11
Reaction score
4
Points
3
Negative, you want the barrel floated in a bolt gun for the same reasons you want it floated in a gas gun. We do not bed barrels in the barrel channel.

You must be talking about bedding the bolt action/receiver to the stock.
Action bedding isn't always needed on a bolt action rifle..... especially if you're not having any accuracy issues at all but it's not a bad idea to bed an action anyway.

This bedding forms a very tight tolerance /form fitting and stronger connection between the action and stock and eliminates the chance for torque being introduced into the action by the action screws due to variabilities in the stock inlet.

Usually this bedding stops at the recoil lug but some will extend the bedding just a bit ahead of the lug to add some contact to the breech area of the barrel.

Thanks for clearing that up, J2, there's plenty to learn as I move from gas guns to bolt guns. Let me ask you and other viewers a related question, then, if when I've bedded the action (if necessary) and dry-fit the rifle, if there appears to be some contact with the stock at spots along the barrel, is it worth opening up the stock's barrel channel a little to prevent that contact? If so, how much? 1/16"? 1/8"? What's a suggested relief amount?
 

FURMAN

Long Range Only Editor
Joined
May 27, 2015
Messages
6,562
Reaction score
8,423
Points
113
Location
Emporia Ks
Thanks for clearing that up, J2, there's plenty to learn as I move from gas guns to bolt guns. Let me ask you and other viewers a related question, then, if when I've bedded the action (if necessary) and dry-fit the rifle, if there appears to be some contact with the stock at spots along the barrel, is it worth opening up the stock's barrel channel a little to prevent that contact? If so, how much? 1/16"? 1/8"? What's a suggested relief amount?
Some tape the barrel to center it into the stock. I disagree with this method as it induces stresses into the system. I do believe you should relieve the stock as you suggest. I don't measure. I go by sight. I would guess around .100-.150".
 

Lance Kenyon

Well-known member
Joined
Aug 29, 2017
Messages
1,636
Reaction score
3,293
Points
113
Location
AZ
Bed the action or have a mini chassis in the stock.

Free float the barrel channel with no contact points.

Works for me.
 

elkguide

Well-known member
Joined
Sep 21, 2018
Messages
816
Reaction score
740
Points
93
Location
Vermont
I use a dollar bill and slide it down the barrel once the action is in place. If the dollars gets bound up, I take a piece of sandpaper and slide it (grit down towards the stock) back and forth until the dollar bill slides freely.
 

jeffpatton00

New member
Joined
Mar 22, 2020
Messages
11
Reaction score
4
Points
3
Lance, can you explain what a mini chassis is? The Savage AccuFit stock has a molded-in aluminum stip which include a cutout for the recoil lug, and the action screws project through the aluminum strip into the action.
 

RBanta66

Well-known member
Joined
Apr 3, 2020
Messages
1,382
Reaction score
2,071
Points
113
Location
Virginia,
So in my early days like 1990 I had a fall from a treestand and broke not only my neck but also the stock to my Rem 700 ADL 270. I healed just fine but finding a new stock took time. I finally found a old ADL short action and just took a Dremel to it and moved the recoil lug and action screws holes. I bought a accuglass kit and bedded the whole thing, action and barrel channel. That rifle would shoot cheap Winchester super X 130gr 3 shots into pretty much one hole, actually it just got bigger but 3 shots were the size of a dime. The 4th shot would walk up about a 1/2 inch as the barrel heated up. However I didn't know anybetter back then and now all my rifles are free floated. I still have that rifle but it's in a different stock. I still have that stock to but it has no recoil pad and well let's just say it talks back with authority..
 

DerekS

Well-known member
Joined
Jan 17, 2021
Messages
652
Reaction score
458
Points
63
Location
Near Tulsa, OK
Thanks for clearing that up, J2, there's plenty to learn as I move from gas guns to bolt guns. Let me ask you and other viewers a related question, then, if when I've bedded the action (if necessary) and dry-fit the rifle, if there appears to be some contact with the stock at spots along the barrel, is it worth opening up the stock's barrel channel a little to prevent that contact? If so, how much? 1/16"? 1/8"? What's a suggested relief amount?
I sand my barrel channels until I can slide a 3x5 note card (card stock) without binding. Bit more clearance than a dollar bill. Used to use dollars myself, just like card stock better these days.
 

jeffpatton00

New member
Joined
Mar 22, 2020
Messages
11
Reaction score
4
Points
3
Great feedback on the barrel clearance. How about the action - J2Shooter noted that the action should be bedded, if necessary. In this case, the Savage AccuFit stock has an aluminum insert molded in, and since there is a slot in the insert for the recoil lug, and the action through-bolts through the insert, does that obviate the need to bed it, or is bedding still useful?

Savage stock insert.jpg
 

DerekS

Well-known member
Joined
Jan 17, 2021
Messages
652
Reaction score
458
Points
63
Location
Near Tulsa, OK
Some guys still skim bed aluminum chassis's. It really depends on how it shoots. If it shoots good, then bedding probably won't make much difference. If it doesn't shoot good, bedding the action might not fix the problem. Bedding is sort of an extra step for utmost accuracy and piece of mind. It's great to do, but most times not necessary.

I have several guns that shoot great (.5 MOA) and I've never bedded them. Just assembled a complete custom for my dad, first for both of us, and I am absolutely going to bed it. It will probably shoot fine without, but I'm doing it anyway.
 

ABC1000

Well-known member
Joined
Dec 27, 2017
Messages
701
Reaction score
392
Points
63
My experience with bedding rifles is that it will make them shoot better but not tons better… I bedded a rifle that didn’t shoot worth a crap and guess what.. still shot crappy though mildly better. I like to verify my gun will shoot if it’s not custom or close to it before I’ll spend a dollar or one minute on a bed job as it’s gotta be pretty accurate to begin with… Though I will verify the barrel free floats or take a Dremel to a stock… I prefer chassis guns now mostly and have found very little benefit in bedding a good chassis but always make sure I’m level and alternate 5-10 in lbs when I’m tightening action screws which helps IMO.
 

ABC1000

Well-known member
Joined
Dec 27, 2017
Messages
701
Reaction score
392
Points
63
Some guys still skim bed aluminum chassis's. It really depends on how it shoots. If it shoots good, then bedding probably won't make much difference. If it doesn't shoot good, bedding the action might not fix the problem. Bedding is sort of an extra step for utmost accuracy and piece of mind. It's great to do, but most times not necessary.

I have several guns that shoot great (.5 MOA) and I've never bedded them. Just assembled a complete custom for my dad, first for both of us, and I am absolutely going to bed it. It will probably shoot fine without, but I'm doing it anyway.
Sorry don’t know how I missed your post and basically duplicated what you said in regards to minor benefits to bedding…
 

Lance Kenyon

Well-known member
Joined
Aug 29, 2017
Messages
1,636
Reaction score
3,293
Points
113
Location
AZ
Lance, can you explain what a mini chassis is? The Savage AccuFit stock has a molded-in aluminum stip which include a cutout for the recoil lug, and the action screws project through the aluminum strip into the action.
Just like you noted.

It is a piece of milled aluminum that is embedded in the stock material, for what is supposed to be a perfect fit for the action, allowing no play. Also called an aluminum bedding block in some stocks.
Just like a chassis is supposed to be.
I have found them to be very close in most cases and have not had to bed any of my rifles that have this feature. It does add a bit of weight to the stock, and they can be just a piece for the action to mount in or can include a DBM bottom metal assembly in the same piece. I have a few of both types. If I want as light as possible, I get a stock without a mini chassis (or aluminum bedding block), and just install aluminum pillars and bed it.
 

Buster1NTX

New member
Joined
Dec 6, 2025
Messages
1
Reaction score
0
Points
1
There's a lot of information on bedding barrels in bolt guns, but I'd like to better understand why bedding is a good thing. In a gas gun, a free-floating barrel is usually preferred for precision, its only connection to the rifle is where it mates to the upper receiver (and of course the gas block), which I believe is intended to minimize contacts which would affect barrel harmonics.

In a bolt gun, however, it's apparently preferred to bed the barrel into the stock, so in my (limited) understanding, this runs counter to the preferred approach with a gas gun. Can you help me understand why minimizing barrel contact is a good thing in a gas gun, but maximizing barrel contact is preferred in a bolt gun? Further, since release agent is used when bedding and the barrel isn't glued to the stock, the barrel is still able to vibrate against the bedding due to harmonics, and potentially able to contact the bedding at different locations at different points in the harmonic sine wave. My application is precision target shooting, if that bears on the issue. Thx for your info.
I realize this is an old thread but after reading the post and replies I decided I must add a comment.

As many have pointed out, the most common recommendation is to bed the action and recoil lug but free float the barrel. This provides an excellent setup for accuracy. It is also the easiest method of producing great accuracy.

However.....

Bedding the action AND barrel can produce superior accuracy as well. It must be done right, but the results are often superior to the free float method.
My favorite and most accurate hunting rifle (a 1970's era Winchester Model 70 chambered in 270 Win) has a bedded action and barrel.
I was never able to achieve better than 1 MOA (most loads proved greater than 1 MOA) no matter what load I tried. While 1 MOA for an off the shelf hunting rifle is good, it would not provide this accuracy with different bullet weights. So, in an effort to improve accuracy I bedded the recoil lug, but this provided no appreciable improvement. Next, I bedded the entire action which made notable improvement but not to the degree I wanted. So, I decided to try bedding the barrel also. The results were amazing. This took my favorite load from 1 MOA to 0.5 MOA. Similar results were noted with different loads and bullet weights after the barrel bedding was completed. In short, the full stock bedding turned out to be an amazing improvement with this rifle.
I duplicated these results a few years later when I bedded the action and barrel on a Remington 700 6mm that was experiencing some notable accuracy issues.
In short, full action and barrel bedding can produce great results when done right.
 

Forum Sponsors

Top