• WE DO LONG RANGE RIGHT.

    JOIN LONG RANGE ONLY

    Ask questions. Share your experience. Talk rifles, reloading, optics, and hunting with people who put their gear to work.

    REAL EXPERIENCE.   SHARED KNOWLEDGE.
    JOIN THE COMMUNITY →
    Free account. Be part of the conversation.
    Already a member? Log in

Best big bore cartridge and platform to choose? 375 CT, 408 CT, 416 Barrett and 50 BMG

ABC1000

Well-known member
Joined
Dec 27, 2017
Messages
701
Reaction score
392
Points
63
I have 7mm and 30 cal magnums for some ELR but nothing of what the 375, 408, 416 (not as interested in 50 this far) cartridges are capable of as far as range. I rarely shoot over a mile now but the range I shoot at has targets out to 2 miles and I’m starting to get away from reclusive shooting on my own and start competing a little bit at my local range.

I’m thinking 375 would be the easiest on the pocket book for volume shooting but also gives better bcs than the 408s or 416s but was considering the 416 until I read about the quality of brass and lack of it in general as well as bullets.

The best bang for the buck at a price point I can afford (I’m not just about lowest price though) from what I’ve found seems to be the Desert Tech HTI. I can get the rifle with a custom aftermarket match barrel, press, reloading dies and equipment, updated targets and all my reloading components for around $8,000 if I go the Desert Tech route. I’ve got a gun builder I’ve used that will sell me the gun with an upgraded barrel (same barrel a lot of the Comp shooters are using but name escapes me) for right at 5k... and that will give me 3k to work with as far as everything else needed to get me started with this platform.

I’ve looked into the AI and Cadex, the Barrett, the Armalite, the McMillan and a couple others and it seems like I’d be into some of these considerably more or they’re not going to be as accurate/sturdy enough (armalite). I’ve also looked a little into David Tubb’s solution of modifying an action and chassis to fit as well but am not sure about this option. I’ve only shot my buddy’s AI and I’m sure the ax50 is one heck of a rifle system but I’d be more than double the cost of what I can get into a desert tech for and that’s before the cost of switching cartridges to get the 375 I’m thinking I want in the first place. Ive heard nothing negative about the Cadex either but that would still be a few thousand more than the DT. I’ve heard about issues with the extractor and springs on DT (mags a bit as well) but that they shoot really well. My gunsmith says he’s had great luck with them with his barrels in a lot of guns he’s put together.

Is there another platform that I should be considering? What was some of your reasoning why you purchased the platform/cartridge you did?
It seems that RCBS is the best option for the 50 press but is there something that I’ve missed? I’m thinking the 390 Hornady A-Tips are a solid option in 375 (408).

Looking for advice...

Aaron
 

Terry

Active member
Joined
Dec 14, 2019
Messages
113
Reaction score
42
Points
28
Location
Sun Prairie, WI
You could build a very nice 37 XC for far less than the major brands, and it would be built to your liking.
 

ABC1000

Well-known member
Joined
Dec 27, 2017
Messages
701
Reaction score
392
Points
63
Thanks for the reply Terry. My buddy and I have built several twin guns to save time on reloading etc and he threw that option out as well. It seems that the 37xc has approx 75 FPS slower velocity but I have heard good things about that cartridge. Do you have any experience with that round?
 

Terry

Active member
Joined
Dec 14, 2019
Messages
113
Reaction score
42
Points
28
Location
Sun Prairie, WI
I have a 37XC. 350 and 375 grain bullets at 3000 fps. easily.
Have not shot the 400's yet.

Using 120 grains H1000 with 350's and 375's.
 
Last edited:

ABC1000

Well-known member
Joined
Dec 27, 2017
Messages
701
Reaction score
392
Points
63
So I just bought the new elite precision savage in 338 as I'm trying to order a 37XC barrel and swap it out. The action is blueprinted so I'm hoping it will be accurate. It is going to take months to get the barrel (still waiting on a call back from SSS about specs for a savage action) so I'm going to shoot the 338LM in the meantime...
I prefer Forster dies on most of my newer guns as they've been super consistent... but haven't neck turned up to this point. Usually I just full length size every time but I hate doing that on my 28 Nos and brass is just about as expensive for 338 LM... what would you recommend for sizing/turning? Aaron
 

Jasent

Well-known member
Joined
Feb 10, 2019
Messages
358
Reaction score
289
Points
63
Location
Deer park wa
I’m loving the 37XC. It is a bit slower than the cheytac but less powder, cheaper action and chassis, great brass and dies,

My current setup is built an a trued savage 112 target magnum. I ordered an unchambered prefit from McGowen and chambered it my self.
My next build will be a tac338 action and k&p 7 twist barrel in 37XC.
 

Forum Sponsors

Top